Faced with fierce competition in the automotive electronics industry's rapid upgrading and market a wide variety of styles tachograph really Tiaohua the majority owners of the eye. From the old-fashioned CTR tachograph, holds many lessons to a common type of camera driving record, to the rearview mirror tachograph rapid spread shape descending, and finally mixed into one body, a majority of car owners travel safety essential tool. So buy a new rearview mirror tachograph, how installed? Good body just can not dismantle, not installed, what kind of car with what kind of bracket? Really nothing.
statement:
1. Since the same type of bracket mounting different models are slightly different, disassembly may be different ways.
2. The same cars in different years in the rearview mirror holder may be different.
3. Based on the network collate the text shown in the rearview mirror removal methods, only for reference and learning exchanges. Subject to the actual situation when the actual construction.
Let us look at the common market Mirrors tachograph bracket Removal tips:
1 bracket:
1 to Highlander example: sitting in the copilot position, left hand grabbed the mirror from the root of the glass close to the right hand moderate force smashed up his left hand, can be removed;
2, Nissan Teana example: with a flat screwdriver package a piece of cloth, pry live beneath the base of the rearview mirror gap, at the same time to push the direction to remove the car roof to stand.
No. 2 bracket:
Honda Civic with an example: mirrors and glass joints are invisible dark buckle, only to see there is a small gap in the plastic lid, dark button hidden inside the lid can be seen separated to a button, the button is pressed a little harder to push up the base of the mirror can be removed.
3 bracket:
In Volkswagen Bora, for example, pinch the base, rotated 90 degrees clockwise or counterclockwise, and then place the mirror himself down. Some cars may be more tight, hard time to pay attention. It must act immediately put back bracket bracket then rotate in place, otherwise the interface
Department prone to cracks.
4 bracket:
Buick Excelle as an example: the thumb and index finger grip the base of the rear-view mirror, to the extrusion direction of the glass roof at the same time to push the direction, do not use brute force. There are two springs inside the base, as long as the spring is loose enough to get up.
6 bracket:
In Harvard H6, for example, from the bottom up, there is a screw. It open. After loosening the screws, put up a mirror the mirror can be removed.
7 stand:
MG 6 with an example: first breaking the mirror parallel to the windshield, and then swing around the mirror, mirror on the left and right Baibai down.
12 bracket:
In the Peugeot 307 as an example: a good frame hand, the other hand grasp the base stand along the slope of the glass can be easily pushed up from the base to the fixed bracket shirk down.
14 bracket:
In New Sail example: There are mirrors on the base of a hexagonal screws with hexagonal screwdriver, loosen counterclockwise and then gently push up the bracket, the bracket can be removed.
15 bracket:
In Fiat Case: Use a Phillips screwdriver to screw the bracket below the rearview mirror knocked off, turn the mirror holder, you can remove the rear-view mirror.
16 bracket:
Cheung Yuet V3 with an example: from the bottom up against the glass, behind a small hole with a cone stuffed like to do it, then put a mirror up and gently push it down.
3B (19) Bracket:
To mark 408 as an example: in front of the mirror first halves together plastic covers were taken off, and then breaking the mirror parallel to the front windshield, then about clever force parallel to the windshield breaking movable mirror , the mirror will automatically down. Similarly mounting bracket, the first partial 60 degrees inside, and then breaking the mirror move naturally tight.
22 bracket:
Audi Q5, for example, remove the U-shaped cover holding bracket counter-clockwise by 45 degrees, you can remove the rear-view mirror.
23 Stand: BMW X5 example: first two and a half in front of the mirror together separate plastic cover removed, then the mirror parallel to the direction of the front gear, left or right twist 60 degrees, bold cautious hand will be dynamic, and on down, when installed as the first 60-degree slant hang in, then tighten positive.
24 Stand: In Volkswagen Magotan example:
When removing, follow these steps:
1. turn off, unplug the car keys to ensure a sense of the rain sensor is not energized;
2. Removal wedge 3409 (see photo), or other tool, open the left cover (below -2- at) the locking member (below -1- place);
3. Loosen the sides of the cover (figure below -2- and -4- Office);
4. disconnected plug connection (below -3- office);
5. Hold the mirror holder, drawn down along the front windshield bracket:
26 Stand: BYD S6 example:
Hold the bracket in the direction of the car's slightly hard breaking it and feel the elasticity of the clamp bracket. After the top edge of a circle, the radius of the stent inwardly breaking, the force appropriate to remove. Black elastic clamp bracket is stuck in the base: when you replace it with an appropriate force to go back to press
27 bracket: VW POLO with an example:
Open the cover of stand base, hand holding the mirror base, along the glass down a smoke, you will be able to take down the inside rearview mirror:
Mount interface can be seen that there are two snaps in the middle there spring clip to strengthen the adhesion of the fixed time:
28 Stand: In Tiggo 3 as an example:
Identify the internal structure of the stent, can be easily removed. There is a tilt mirror bracket sheet iron stuck base, pull it out straight.
With a small screwdriver inserted into the hole, the top forward a little harder, you can remove:
30 Stand: Porsche Cayenne as an example:
First remove the black plastic cover rearview mirror connected with the dome light, triangular structure, and then separate the plastic shell mirror base, spread apart, the last rotating mirror base counter-clockwise, and came down
32/33 bracket: BMW and MINI in the new Volvo S80 as an example:
First, the rearview mirror ornaments cover removed, then grab hand mirror, mirror in one hand and grasp the bracket, twist 45 degrees to the right on down, and vice versa when installed.
36 bracket: to import new Volvo XC60 example:
First, the rearview mirror ornaments cover removed, then grab hand mirror, mirror in one hand and grasp the bracket, twist 45 degrees to the right on down, and vice versa when installed.
37 bracket: Mercedes-Benz E260L example:
After the first car of the original decorative panels and ceiling partially removed, drop down the original car rearview mirror support rod can be removed, if too tight can use a slotted screwdriver into the gap behind the auxiliary Qiaoxia, when you install some Mercedes-Benz models will be a little loose Workaround: after installing the bracket will see the edge of a screw two fixed base, you can twist the screw shim underneath the gasket will get stuck on such a twist bracket to prevent it from loosening.
The above is common rearview mirror tachograph stent removal methods, more information please pay attention BEST tachograph public micro signal.
|
